Power & light
- Fused distribution panel — $240
- Cargo-area LED strip, switched — $160
- Awning light circuit with plug — $190
- Inverter mount and wiring — from $320
Builds & specifications
Every job quoted off a written sheet
Below is what we build, what goes into it and what it costs. Prices are for supply and fit at Mountain Street 78, Ultimo. Vehicle-specific templating is included — we don’t charge extra for an odd load area.
01 — Drawer systems
Built on the bench in Ultimo, fitted the same week.
Single drawer
Base- One full-width drawer up to 1,100 mm deep
- 17 mm structural ply carcass, black matt finish
- 150 kg rated runners, twin positive locks
- Rubber-matted top deck
$2,450
Twin drawer
Popular- Two independent drawers, split 50/50 or 60/40
- 227 kg sealed ball-bearing runners, soft close
- Adjustable internal dividers per drawer
- Recessed tie-down track in the deck
$3,380
Drawer + fridge slide
Combo- One drawer plus a rated slide sized to your fridge
- Optional tilt slide for high wagon floors
- Fridge socket wired into the drawer face
- Chassis-backed mounting plates
$3,690
Steel canopy fitout
Heavy- Powder-coated steel frame for tray canopies
- Drawers, shelving and water-tank bay in one module
- Sealed cable runs through gland plates
- Quoted after templating — price is a starting point
from $5,900
02 — Dual-battery systems
Sized on run-time, not on guesswork. Tell us your fridge and your longest stretch off mains.
Weekender — 100 Ah AGM
Spec- 100 Ah deep-cycle AGM in a vented cradle
- 25 A DC-DC charger with solar input
- Fused both ends, loomed and labelled harness
- One fridge socket plus rear Anderson outlet
$1,290
Tourer — 120 Ah lithium
Popular- 120 Ah lithium with internal BMS and low-temp cut-out
- 40 A DC-DC charger, dash-mounted monitor
- Two fridge sockets, USB-C PD, front and rear Anderson
- Under-deck or in-drawer mounting, restrained to rating
$2,740
Remote — 200 Ah+ lithium
Long haul- 200 Ah or twin-bank lithium for extended remote trips
- 50 A DC-DC plus dedicated MPPT solar controller
- Inverter-ready bus bars and shunt monitoring
- Full circuit map and spare fuse kit supplied
from $4,150
Battery swap & upgrade
Fix- Tired AGM replaced with lithium, charger re-profiled
- Old VSR / solenoid setups converted to DC-DC
- Cable sizing corrected for voltage drop
- Old hardware handed back or recycled — your call
from $780
03 — Add-ons & extras
Bolt these onto any build while the rig is already in the bay.
Storage & restraint
- Drawer-top deck with tie-down track — $390
- Rated cargo barrier interface — from $280
- Jerry and water-tank cradles — from $210
- Drawer dividers and gear sleeves — $70 each
Charging
- Roof solar plug with sealed gland — $180
- Fixed roof panel install — from $890
- 240 V AC charger with external inlet — from $460
- Trailer charge circuit — from $250
Service & support
- Pre-trip system check — $120
- Free re-torque after your first trip — $0
- Electrical diagnostic, 45 minutes — $95
- Drawer refurbish and runner replacement — from $290
Materials we stand behind
No unbranded chargers, no undersized cable, no chipboard.
- Structural ply 17 mm
- Powder-coated steel
- 227 kg runners
- Tinned copper cable
- Marine-grade lugs
- ANL & MIDI fusing
- Split loom & braid
- LiFePO4 chemistry
- DC-DC chargers
- MPPT controllers
- Anderson connectors
- Rated anchor points